Christian Feldmann
REHVA Fellow - AICVF (France)
christian.feldmann@voila.fr
 

Foreword

Since 1974 several regulations have progressively strengthen thermal performances of buildings in France. But the latest one called RT 2012 based on requirements settled by the 2008 national convention ”Grenelle de l ‘Environnement” is a significant step towards nZEB buildings.

RT 2012 which has been in force since January 1st, 2013 applies to all new heated or cooled buildings, except

·   provisional buildings

·   buildings heated with an indoor temperature lower than 12°C

·   buildings heated or cooled for other reasons than comfort, for example industrial processes

·   farms

·   churches

·   buildings located in French overseas territories.

 

General

Three main requirements

RT 2012 building regulation includes mainly three major requirements which must be respected simultaneously.

1.   The first one deals with the intrinsic features of the structure and the envelope of the building without considering the HVAC system and other technical facilities. Such features are specified with the Bbio Factor (bioclimatic needs factor).

2.   The second one involves the maximum permitted annual consumption of primaryenergy of the building taking into account performances of HVAC system, DHW production and, if any, artificial lighting through the Cep factor.

3.   The third corresponds to requirement for thermal comfort in summer based on the compliance with a maximum comfort calculated temperatureTic.

RT2012 also includes some specific prescriptive requirements (see example in the end of the article).

Two main categories of buildings

Two main categories of buildings are considered in the RT 2012 regulation.

Category CE2

Buildings belonging to category CE2 mainly depends on the usage type of the building, noise exposure and geographical location. It is defined in detail in the decree. Basically buildings built in noisy areas where it may be necessary to install air conditioning system in order to ensure thermal comfort in summer while the windows are kept closed are allowed to be included in category CE2.

Roughly it can be considered that dwelling, school and office buildings located in noisy areas in the hottest regions of France falls within CE2 category.

Category CE1

All others buildings belong to category CE1.

 

Bbio Factor

Bbio factor is a dimensionless number expressed by a number of points calculated using the following relationship:

Bbio = 2 x (Heating needs + Cooling needs) + 5 x (Artificial lighting needs)

in which heating, cooling and lighting needs of the building, are calculated by an hourly dynamic analysis software.

Energy consumption of ventilation system and lighting facilities are based on conventional values included in the software.

Bbiomax

Bbiomax is the maximum permissible value of Bbio for a given building project, the regulatory requirement being

Bbio building project < Bbiomax

Bbiomax satisfies the following relationship:

Bbiomax = Bbiomaxmoyen x (Mbgeo + Mbalt + Mbsurf)

where

·    Bbiomaxmoyen is a coefficient depending the use and the category (CE1 or CE2) of the building

·   Mbgeo: geographical location coefficient

·   Mbalt: altitude location coefficient

·   Mbsurf: a modulationfactor, in terms of surface of the premises. Mbsurfis only usedfor housing, commercial buildings and sports halls.

 

For example, in case of sports halls building, Mbsurfis given by the following rule:

If Building Floor Surface (BFS) ≤ 1 000 m²then Mbsurf= −0.008 x BFS + 0.8

If BFS > 1 000 m²then Mbsurf =0

Bbio factor for an office building

·   Bbiomax = 70 if the building belongs to category CE1, Bbiomax = 140 for category CE2.

·   Mbsurf = 0

·   Mbalt (altitude location coefficient):

 

Altitude

Mbalt

From 0 to 400 m

0

From 401 to 800 m

0.1

800 m and over

0.2

 

The values of Mbgeo (geographical location coefficient) are given in the table below depending on the area in the map:

Category

Geographical areas

 

H1a

H1b

H1c

H2a

H2b

H2c

H2d

H3

CE1

1.10

1.20

1.10

1.10

1.00

0.90

0.80

0.80

CE2

1.00

1.00

1.00

1.00

1.00

1.00

1.20

1.20

 

Cep coefficient

Cep coefficient represents the conventional annual consumption of primary energy of a building, reduced to the floor surface. The counting of floor surface is stated in a government ordinance.

Only two primary energy factors are applied, for electricity 2.58, and for all other fuels 1.

Cep, expressed in Wattsep /m² per year takes account energy used to meet the following needs of the building:

·   heating

·   cooling

·   domestic hot water

·   lighting

·   auxiliaries (fans , pumps).

 

If any, energy produced on-site from renewables may be deducted from the calculation of Cep.

Regulatory requirement

The regulatory requirement is met if:

CepCepmax

Cepmax is defined with the following equation:

Cepmax  = 50 x Mctype x (Mcgeo + Mcalt + Mcsurf + McGES)

Where:

·   Mctype is a coefficient depending the type and the category (CE1 or CE2) of the considered building to which it belongs

·   Mcgeois geographical location coefficient

·   Mcaltis altitude location coefficient

·   Mcsurf is acoefficient depending the floor surface for housing, commercial buildings and sports halls

·   McGESis acoefficient depending on the greenhouse potential of the fuel used.

 

Typical values of Mc coefficients

Housing buildings

Values of the various coefficients which have to be used in the Cepmax relationship, for housing buildings, are given below.

·   Mctype = 1

·   Mcgeo values, depending on the region of the country, are given in the table below:

 

Geographical area

H1a

H1b

H1c

H2a

H2b

H2c

H2d

H3

Mcgeo

1.20

1.30

1.20

1.10

1.00

0.90

0.90

0.80

 

·   Mcalt(altitude coefficient) depends on the altitude of the building location:

 

Altitude

Mcalt

0 to 400 m

0

401 to 800 m

0.2

801 m and over

0.4

 

·   Mcsurf is given by formula, depends if it is a detached house or a collective residential building

·   McGES is fuel greenhouse potential

·   Wood fuel McGES = 0.3

·   When building is linked to a District Heating Network McGES = 0 to 0.3 (depending the fuel used for the district heating plant)

Case of office buildings

·   Mctype = 1.4 if building belongs to CE1 category, 2.2 if CE2 category

·   Mcgeo = values depend on both region of location and category of the building:

 

Geographical area

Category

H1a

H1b

H1c

H2a

H2b

H2c

H2d

H3

Mcgeo

CE1

1.10

1.20

1.10

1.10

1.00

0.90

0.80

0.80

Mcgeo

CE2

1.00

1.00

1.00

1.00

1.00

1.00

1.20

1.20

 

·   Mcalt (altitude coefficient) depends on the altitude of the building location:

 

Altitude

Mcalt

0 to 400 m

0

401 to 800 m

0.1

801 m and over

0.2

 

·   Mcsurf = 0

·   McGES When building is linked to a District Heating Network = 0 to 0.3 (depending the fuel used for the district heating plant)

 

Maximum Cep values for individual houses and non air-conditioned office buildings

The figures below show the maximum permitted values of Cepmaxfor individual houses and non-air conditioned office buildings (CE1 category) depending the geographical region. On sea level altitude = 0 m, in the case with McGES = 1.

 

Individual houses:

 

 

Non air conditioned office buildings:

 

Maximum air indoor temperature

The third performance requirement set by the new regulation is the respect of a maximum indoor operative temperature called Tic (for “Temperature intérieure conventionnelle"). This requirement is only requested for non air-conditioned buildings.

Tic is calculated by a module of the regulation software. Corresponding requirement is that hourly calculated value of Tic might not be upper than Ticref.

Ticrefcan never be less than 26°C.

The calculation method of Ticref is being revised. A new version should be available in the coming months.

Complementary prescriptive requirements

Besides the three main performances requirements described above some wherewithal exigencies are listed in RT2012.

Some of them are given below as examples.

·   Walls thermal insulation

Albeit the thermal quality of the building envelope is already considered in the Bbio coefficient some complementary exigencies are intended:

o        U- value of a wall separating an unheated room and an heated room must not be higher than 0.36 W/m²K

 

o        Overall linear thermal transmission ratio (thermal bridges) of the whole building must be less than 0.28 W/m²Floor SurfaceK:

 

Σ(Ψ,L) / Building overall Floor surface < 0.28 (W/ m²Floor Surface K)

o        Thermal bridges between intermediate floors and facades less than 0.6 W/m K

 

·   Air tightness of the building envelope

Airtightness of the building envelope measured according to EN 13829 measuring method (Blower door) must be in accordance with the values of the table below

 

Q (m³/h,m²)

Individual or attached houses

0.6

Collective housing buildings

1.00

 

It must be underlined that surface being considered is that of internal walls, floor surface being excluded.

·   Natural lighting

For housing buildings the total windows area must be more than 1/6 of the floor surface area of the flat.

·   Thermal comfort in summer

In bedrooms Solar Heat Gain Coefficient of the windows is limited according to the orientation of the façade. Lower values of SHGC are required when the building is located in a noisy area.

Application of the regulation

All calculation must be compulsorily performed by an authorized software based on the official rules Th BCE-2012 established by Centre Scientifique et Technique du Bâtiment (CSTB).

Christian FeldmannPages 29 - 32

Stay Informed

Follow us on social media accounts to stay up to date with REHVA actualities

0

0 product in cart.products in cart.